401 rebuild

301, 401, plinths and assorted idler stuff
Post Reply
Ant
Shed dweller
Posts: 2332
Joined: Mon Jul 31, 2017 6:45 pm
Location: Yorkshire

#1 401 rebuild

Post by Ant »

Just finished this one for savvypaul, or 99.999% finished, bloody feet still haven't turned up...

ImageGarrard 401 ortofon ta210 spu dynavector ultimo 20a by anthony cresswell, on Flickr

In that shot it temporarily has a borrowed SPU on it to check that the alignment was spot on, which it is. It will have an SPU on it when it goes home. As the SPU is not mine, it was then taken straight back off and stored away snug in its box.
It has some temporary feet on it to make it useable until the proper ones finally turn up. or don't, in which case i will be mildly annoyed an have to make some

ImageGarrard 401 ortofon ta210 spu dynavector ultimo 20a by anthony cresswell, on Flickr

Its a big bugger at about 23 1/2" wide, that monstrous ortofon ta210 arm is longer than most 12" arms in terms of spindle to pivot distance. They usually range somewhere around 290-295mm, that ortofon is 316.5 so is about an inch further out than the norm.

ImageGarrard 401 ortofon ta210 spu dynavector ultimo 20a by anthony cresswell, on Flickr

spinning 12" singles is fun, the Missus is collecting them at the moment, mostly 80s stuff. They don't half sound good though so I'm not complaining... Much....

ImageGarrard 401 ortofon ta210 spu dynavector ultimo 20a by anthony cresswell, on Flickr

I put the dynavector ultimo 20a in it once the SPU was put away. The arm needs alot of headshell weight to balance up, the headshell that comes with it is a 15g one, so all up with that cart in it its about 25g on the end of the arm. It does mean that medium to high compliance carts wont like it, I put the SL15 E LL (one of our wills favourites) in the headshell and got an immediate resonance out of it because the SL is high compliance at 24. the SPU is 8. A different bit of rubber was used in the assembly to make it useable with SME arms in 1968 when it was made. The Dynavector compliance is also listed as 8, its probably abit more but not a huge amount, id estimate about 12 ish so it works fine

ImageGarrard 401 ortofon ta210 spu dynavector ultimo 20a by anthony cresswell, on Flickr

Its on some different feet right now to raise it up higher as the arm cable that comes with the ortofon is a stupid gargantuan cable that looks like it could string a suspension bridge. its not very bendy, about a half inch thick, and is cumbersome and awkward to use. Don't even think about using on a suspended subchassis deck, it would be utterly impossible to get it to work. In the earlier shots Id used a different cable. But other than the stupid cable the arm is rather nice.
The feet were actually made by Richard Higgins, they came with one of the very first lencos I had. That one became the first teardrop shaped 75 I did and is still going strong at mi dad's. It's been arou d the block that one...

It will be here for a little while until it gets collected, so ill get to enjoy it for a short time
on to the next one :mrgreen:
Also starring Rex Hamilton as Abraham Lincoln

www.bte-designs.weebly.com
User avatar
IslandPink
Amstrad Tower of Power
Posts: 10041
Joined: Tue May 29, 2007 7:01 pm
Location: Denbigh, N.Wales

#2 Re: 401 rebuild

Post by IslandPink »

Classic stuff !
"Once you find out ... the Circumstances ; then you can go out"
User avatar
Ali Tait
Eternally single
Posts: 4373
Joined: Fri Jun 08, 2007 8:10 pm
Location: Galashiels

#3 Re: 401 rebuild

Post by Ali Tait »

Very nice Ant, great job as always.
User avatar
Mike H
Amstrad Tower of Power
Posts: 20157
Joined: Sat Oct 04, 2008 5:38 pm
Location: The Fens
Contact:

#4 Re: 401 rebuild

Post by Mike H »

Image
 
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
Ant
Shed dweller
Posts: 2332
Joined: Mon Jul 31, 2017 6:45 pm
Location: Yorkshire

#5 Re: 401 rebuild

Post by Ant »

Feet finally arrived midweek so it's complete now. I've also done some work on the motor unit as it was getting right on my tits.
There was a barely audible pitch variation, that once heard, can't be unheard. Watching the strobe, the markings were moving forward and backward erratically, but slowly. As if tracing a square. First going forward, then halting then moving backward then stopping and repeating. Some component hitting a tight spot in its rotation. There is a slight machining error on the strobe markings so it looks like it moves up and down. It was moving up when it stopped after going forward, and down after it went backwards. Which also made me look at components rotating at slow speeds as it was altering every half rotation. If it was the motor it would be fluctuating much faster.
So I cleaned all the drive surfaces with degreaser, lightly sanded the platter drive surface with 1200 grit wet and dry, re dressed the idler wheel, checked and lubed the idler bushes, and pulled the bearing. Cleaned, rebuilt, and re-oiled, it's pitch stable again, and the strobe isn't wandering around anymore. The thrust pad needs replacing though, there is a fairly large flat on the top so I've ordered another one from peak hifi. When I had mine I used a ball bearing one as a replacement, but I went with theirs as its as close as possible to what Garrard designed in the first place. I figure they did it for a reason.
Good job it's still here, if it was getting on my wick, chances are it would have got on Paul's nerves after a while too....
Also starring Rex Hamilton as Abraham Lincoln

www.bte-designs.weebly.com
scotty38
New User
Posts: 1
Joined: Thu Aug 22, 2019 7:12 pm

#6 Re: 401 rebuild

Post by scotty38 »

Great work Ant, hoping the next one will be as good :wink: :wink: :wink:
User avatar
Mike H
Amstrad Tower of Power
Posts: 20157
Joined: Sat Oct 04, 2008 5:38 pm
Location: The Fens
Contact:

#7 Re: 401 rebuild

Post by Mike H »

Excellent! Image
 
"No matter how fast light travels it finds that the darkness has always got there first, and is waiting for it."
Will
Old Hand
Posts: 497
Joined: Mon Jun 11, 2007 10:35 pm
Location: Northumberland

#8 Re: 401 rebuild

Post by Will »

Wonderfull Ant..
Post Reply